Jump to content

  • Welcome to Auto Parts Forum

    Whether you are a veteran automotive parts guru or just someone looking for some quick auto parts advice, register today and start a new topic in our forum. Registration is free and you can even sign up with social network platforms such as Facebook, X, and LinkedIn. 

     

Serpentine Belt Wear Indicators

NAPA

By NAPA
in Napa Auto Parts Forum

 Share

Recommended Posts

NAPA Enthusiast

NAPA

Posted
Posted

Your engine’s

link hidden, please login to view
is probably not something you check on very often. If it is working then your vehicle will run, the battery will charge, the power steering works, and the engine stays cool. But if that belt were to break you will likely be stuck on the side of the road waiting for a tow truck. That’s why it is important to learn the signs of a bad serpentine belt before it fails.

Cracking

One of the common signs of bad serpentine belt condition is cracking. With the engine turned off, pop the hood and grab a flashlight to inspect the serpentine belt. If you see more than three cracks in the belt along the same three inch section, it is time for replacement. Be aware though that some modern serpentine belts are made from materials like EPDM (ethylene propylene diene monomer). These materials are highly resistant to cracking, so a belt that is well past its prime may still look good with no cracking, so it is best to keep checking for other wear indicators if you suspect a worn belt.

Squealing

A belt that is no longer able to grip the engine pulleys may begin to squeal as it slides over them rather than spinning them. This leans to even more accelerated wear of the belt as well as putting heat into the belt via friction. Even if the squealing goes away, don’t ignore it. Normal serpentine belt operation should be nearly silent.

A

link hidden, please login to view
can also cause the serpentine belt to slip so be sure to check it or else your new serpentine belt may have a short service life.

If the belt is chirping like a bird the problem might be one or more accessory pulleys are out of alignment. Not only is this annoying but it will also cause the serpentine belt to wear out faster or even cause the belt to come off.

Worn Out

Modern serpentine belts are actually pretty well engineered to resist physical damage. But just because a belt isn’t cracked or falling apart doesn’t mean it is still good. Just like a car tire the surface material on a belt can wear down. When this happens the ribs on the belt lose their original tight tolerances, and therefore their grip on the engine pulleys. The belt may still fit fine on the pulleys, but it won’t be fully contacting the pulley. The belt may actually end up riding on just the pulley ridges which makes for a tiny contact patch.

Mileage

Even the best serpentine belt doesn’t last forever. If you have been inspecting your serpentine  belt regularly and it still looks fine, you should still replace it every 90,000 regardless. Even without any of the signs of worn serpentine belt life racking up that much mileage means it is time for the belt to move on. If you can’t remember when you change your serpentine belt, it is probably time.

Electrical Gremlins

One of the lesser known signs of bad serpentine belt condition is an electrical system that starts to act up. Modern vehicles are chock full of computers, modules, sensors and more components that rely on certain conditions to remain constant, like voltage. If the serpentine belt is worn to the point where it no longer spins the alternator consistently there could be variation in alternator output. You may even get a check engine light for random systems issues. If you are pulling your hair out chasing electrical issues, check the alternator output for consistency. If it is jumping all over the place a worn serpentine belt may be the issue.

Not So Cold AC

Another one of the not so common signs of a worn serpentine belt can be a weak AC system. Your air conditioning compressor takes a bit of engine power to turn. You’ve probably noticed that in a car with a small engine turning off the AC feels like it gives you a bit of a power boost. If the serpentine belt can’t grip the AC compressor clutch, it also can spin it to compress the refrigerant back into a liquid to cool you off. You might hear a squealing sound when the AC compressor cycles on, but don’t rely on sound as the only symptom. If your AC isn’t blowing as cold as you remember and you can’t remember when you changed the serpentine belt, it is probably time for a belt replacement. 

Diagnosing a worn out serpentine belt isn’t as easy as it used to be, but the signs are all there if you are paying attention. Luckily serpentine belts are usually affordable and

link hidden, please login to view
, so when the time comes there’s no excuse to put it off.

Check out all the

link hidden, please login to view
available on
link hidden, please login to view
or trust one of our 17,000
link hidden, please login to view
for routine maintenance and repairs. For more information on diagnosing engine drive belt tensioner failure, chat with a knowledgeable expert at your
link hidden, please login to view
.

The post

link hidden, please login to view
appeared first on
link hidden, please login to view
.

link hidden, please login to view

Sell your car with CarBrain

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing

  • Similar Topics

    • Dorman Products
      Rust Belt vs Salt Belt: Do you know the difference?
      By Dorman Products
      Rust Belt vs Salt Belt: Do you know the difference?
    • Counterman
      Serpentine Belts Have a Strong Supporting Cast
      By Counterman
      You might not be able to see it, but an accessory-drive belt is always both speeding up and slowing down. When a piston accelerates downward after the ignition of the fuel and air, the crankshaft speeds up and then slows down as it reaches the bottom of the stroke. These changes in speed are minimal, but big enough to cause problems over time.
      If the pulses aren’t minimized, they can hammer the belt and the attached rotating components. On a four-cylinder engine, the degrees of rotation between power pulses are greater than on a V-8 – so the amount of change in speed on the four-cylinder pulley is greater than on a V-6 or V-8. This has a direct effect on how the belt system is designed.
      The belt-drive system is working hardest when the engine is at idle. When the engine is below 1,000 rpm, the alternator, A/C compressor and power-steering pump are putting the greatest strain on the belt.
      Some of the forces can be taken up by the belt slipping on the pulleys. But, slipping causes friction and wear on the belt, as well as flutter. Over time, the slipping can get worse as removal of material from the ribs causes the belt to bottom out.
      There are three components that help to keep the belt on the pulleys without slipping. The tensioner, harmonic balancer and decoupler pulley work together to keep the accessory-belt system quiet and the belt lasting until the replacement interval.
      Tensioner
      The tensioner applies force on the belt. Some tensioners have devices that dampen the movement of the spring and arm, helping to keep constant force on the belt even under a wide variety of conditions.
      Harmonic Balancer
      The harmonic dampener puts a layer of soft material between the crankshaft and outer ring of the pulley. The material helps to dissipate the power pulses and resonant frequencies. While the dampener may only flex one or two degrees of movement, this takes a lot of strain off attached components.
      Decoupler Pulley
      Some alternators have a decoupler pulley. This device serves two purposes. First, it helps to decouple the pulley from the alternator with a one-way clutch. The decoupler reduces parasitic losses by not having to fight against the momentum of the armature in the alternator while the engine is decelerating and accelerating.
      Some decoupler pulleys have a spring and friction dampener to reduce vibration. When an alternator decoupler pulley is compromised, it can no longer absorb the same level of abuse, which has a trickle-down effect throughout the system.
      Alternator decouplers and pulleys should be inspected every 10,000 miles for wear. Early design versions have a service life of 40,000 to 60,000 miles, with more recent versions lasting more than 100,000 miles.
      When inspecting a decoupler or pulley, there are two signs that replacement is needed. First, after shutting down the engine, if there’s an audible buzzing, the bearings in the pulley have likely failed. The second sign depends on whether the vehicle has a one-way clutch (OWC), overrunning alternator pulley (OAP) or decoupler (OAD).
      With the inspection cap/cover removed and the center locked, turn the pulley or decoupler with the appropriate tool. If it’s an OAP or OWC, the pulley can only be turned in the clockwise direction. If it’s an OAD, a counterclockwise turn will reveal a noticeable increase in spring force; a clockwise turn will only have slight resistance. The tensioner, harmonic balancer and decoupler pulley work together to keep the belt in contact with grooves in the pulleys. The three components are engineered together to match the engine. If one part is compromised, all are compromised, including the belt.
      The post
      link hidden, please login to view appeared first on link hidden, please login to view.
      link hidden, please login to view
    • Counterman
      Litens Campaign Emphasizes Proper Belt-Drive Maintenance
      By Counterman
      Litens Aftermarket introduced its new “System Reset” campaign, aiming to bring awareness to the importance of proper drive-belt system maintenance.
      In an effort to educate professional vehicle service technicians, Litens details what a system reset entails, its significance and the potential repercussions of neglecting this essential maintenance step when replacing a drive belt.
      For a belt-drive system to perform optimally, the system’s components must be properly maintained and in tune with each other throughout the lifespan of the vehicle. When it’s time to replace the drive belt, it’s also time to replace the drive-belt system’s tensioners and pulleys. The system is properly reset when all components of the belt-drive system, including the tensioner, idler pulley(s) and the belt, are all replaced at the same time.
      “As vehicle belt-drive systems become more complex, we’re aiming to equip technicians with both education and solutions,” said Scott Howat, national sales manager, Litens Aftermarket. “Properly resetting the belt-drive system enables the technician to reset the vehicle to its optimal OE level of performance.”  
      Benefits of a system reset – replacing the tensioner and idler pulley(s) along with the belt – include enhancing the system’s reliability and longevity, as well as reducing the risk of component failure and subsequent breakdowns. Resetting all of the belt-drive system components together promotes optimal power transmission, minimizing slippage and improving overall efficiency, which can contribute to enhanced fuel economy and performance. 
      Failing to fully reset the system can lead to imbalanced stress distribution, reduced overall system efficiency and premature wear of both the newly replaced parts and the remaining older components. This could result in increased friction, potential belt slippage and an elevated risk of component failure, ultimately compromising the entire belt-drive system’s reliability and performance.
      Litens designs OE belt-drive systems and components to last for a designated period of time. While that number also depends on miles driven and the number of vehicle starts/stops, the belt-drive system typically runs for 100,000 miles before needing maintenance. As all of the system’s components are designed to work together, when the belt is due for replacement, it’s highly likely that the rest of the components in the system are also due.
      For more information, visit 
      link hidden, please login to view. The post
      link hidden, please login to view appeared first on link hidden, please login to view.
      link hidden, please login to view
    • Counterman
      Litens Belt Tensioner Boasts Improvements to OE Design
      By Counterman
      Litens Aftermarket recently introduced its latest OE improvement, the 999420A belt tensioner.
      This new tensioner boasts improvements to the OE design, enabling an efficient belt-tensioner replacement process by a single technician, according to Litens.
      “This tensioner was engineered to improve upon the OE design by addressing the challenges technicians encounter during the installation of belt tensioners, particularly in the confined spaces of engine compartments,” Litens explained in a news release. “Focusing on ease of installation, Litens integrated a design advancement to simplify the installation process significantly.”
      The design upgrade is the lift feature, strategically placed in an offset position between the mounting bolts that secure the tensioner – adding an extra inch under the lip for a technician, providing greater ease of access.
      Typically, a tensioner is located at the side of the engine compartment where there’s very little room for working hands to get a wrench on the tensioner to loosen the belt during installation. The configuration in the Litens tensioner facilitates easy access for technicians to position their wrench when loosening the belt, streamlining the installation process even in the tightest engine compartments, according to the company.  
      Additionally, the lift feature is designed for a 14-millimeter hex wrench consistent with OE design, rather than using a 15-millimeter hex wrench traditionally used on aftermarket tensioners. Consequently, Litens says, the technician has one less tool to keep track of throughout the replacement process. 
      “As an engineering company that manufactures parts, we recognize the struggles that come with installing these parts in tight space,” said Randy Wolters, product manager, belt-tensioning products, Litens Aftermarket. “With these design improvements we’re able to give the tech an extra set of hands and save them from the bloody knuckles you get when working in such a tight space.” 

      link hidden, please login to view is available for all Mazda applications between the years 2006 through 2017, covering a total of 30,000 vehicles in operation. The post
      link hidden, please login to view appeared first on link hidden, please login to view.
      link hidden, please login to view
    • Counterman
      Litens Adds 18 New Belt-Drive SKUs 
      By Counterman
      Litens Aftermarket recently introduced 18 new SKUs to its product lineup, consisting of pulleys, belt tensioners and overrunning alternator decoupler (OAD) pulleys.
      The new SKUs represent an increase in coverage for more than 9.2 million additional vehicles in operation (VIO), including more than 310,000 2023-model vehicles.
      The portfolio additions are for late-model Ford, Hyundai, Porsche, Mercedes Benz, Jeep, Chevrolet and Toyota vehicles.
      Litens now offers more than 900 pulleys, belt tensioners and overrunning alternator decoupler pulleys, with SKUs covering more than 275 million VIO, according to the company. 
      “Our continuous expansion of belt-drive products demonstrates our ongoing commitment to maintaining our position as the global leader in this product category,” said John Lussier, president of Litens Aftermarket. “Litens is the world’s largest OE supplier of belt-tensioning products, and we pride ourselves on being first-to-market in the aftermarket.”
      For more information, visit
      link hidden, please login to view. The post
      link hidden, please login to view appeared first on link hidden, please login to view.
      link hidden, please login to view

×
×
  • Create New...